Your one rep max, or 1RM, is the most weight you can lift for a single complete repetition with good technique. Testing a true max is tiring and carries more risk, especially for newer lifters, so most people estimate it from a normal working set instead. Enter the weight you lifted and how many clean reps you completed (1 to 12), choose kg or lb, and the calculator returns three estimates, their average, and a percentage chart you can use to plan training weights. The estimate is a planning number, not a target you must hit on the day.
On this page
The three 1RM formulas
Each formula was fitted to data from lifters testing reps against known maxes. They agree closely at low reps and drift apart as reps rise.
| Formula | Equation | Source |
|---|---|---|
| Epley | weight x (1 + reps / 30) | Epley, 1985 |
| Brzycki | weight x 36 / (37 - reps) | Brzycki, 1993 |
| Lombardi | weight x reps^0.10 | Lombardi, 1989 |
The calculator shows all three and an average, because no single formula fits every lifter or every exercise. Lifters with more muscular endurance tend to do more reps at a given percentage, which makes high-rep estimates less precise.
Worked example
Say you squatted 100 kg for 5 clean reps.
- Epley: 100 x (1 + 5 / 30) = 100 x 1.1667 = 116.7 kg
- Brzycki: 100 x 36 / (37 - 5) = 3,600 / 32 = 112.5 kg
- Lombardi: 100 x 5^0.10 = 100 x 1.1746 = 117.5 kg
- Average: (116.7 + 112.5 + 117.5) / 3 = 115.6 kg
A reasonable planning max is about 115 kg. If you then want to train at 80% of that, you would load about 92 kg.
How to use the one rep max calculator above
- Pick a lift you have done recently with consistent technique.
- Enter the weight and the number of reps you finished without a breakdown in form. Do not count a rep that needed a spotter.
- Choose kg or lb. The formulas work the same in either unit.
- Read the three estimates and the average. Use the average, or the lowest value if you want to be conservative.
- Use the percentage chart to set your working weights.
For the best estimate, use a set of 3 to 6 reps taken close to, but not at, failure. Sets of 10 or more reps give a rougher estimate.
Percentage chart and typical reps
The chart below the result lists 50% to 100% of your estimated max in 5% steps, with typical rep counts. These rep counts are commonly published averages (for example in the NSCA's Essentials of Strength Training and Conditioning, 4th edition, 2016) and individual lifters vary.
| % of 1RM | Typical reps possible |
|---|---|
| 100% | 1 |
| 95% | 2 |
| 90% | 3-4 |
| 85% | 5-6 |
| 80% | 7-8 |
| 75% | 9-10 |
| 70% | 11-12 |
| 65% and below | 12+ |
Lower percentages are often used for technique, warm-up sets and higher-rep muscle-building work. Higher percentages are used for strength blocks and peaking.
Mistakes to avoid
- Counting grinders or half reps. A rep with a big form breakdown inflates the estimate.
- Mixing exercises. A bench press max tells you nothing about an incline press. Estimate each lift separately.
- Chasing the number every week. Estimates move up and down with sleep, food and fatigue. Look at the trend over several weeks.
- Using sets of 15 or more. The formulas were not designed for very high reps, which is why the calculator stops at 12.
- Testing a true max without preparation. If you do attempt one, warm up thoroughly, use safety pins or a spotter, and work with a qualified coach if you are new to heavy lifting.
General fitness information, not medical advice. If you have an injury, a medical condition, are pregnant, or are under 18, check with a doctor or qualified professional before heavy lifting.
Log it in your free athlete profile
Your free P2ES athlete profile includes a workout log, so you can record the sets you used for these estimates and see how your numbers change over time. It is free for athletes. If your gym uses P2ES Gym, your trainer can see the lifts you choose to share and build your next block from them.
Questions
Lift a weight you can handle for 3 to 6 clean reps, then use a formula such as Epley: weight x (1 + reps / 30). For 80 kg x 6 reps that gives 80 x 1.2 = 96 kg. Averaging Epley, Brzycki and Lombardi, as the calculator does, smooths out differences between formulas.
None is best for everyone. Studies comparing them, such as LeSuer and colleagues (1997), found most prediction equations are reasonably close at low rep counts and less reliable at higher reps. Epley and Brzycki give almost identical results around 10 reps. Using an average of several formulas is a sensible middle ground.
Many coaches re-estimate every 4 to 8 weeks, at the end of a training block, rather than weekly. You can estimate from ordinary working sets without a separate test day, so it costs little extra fatigue. Track the trend in your workout log rather than reacting to one session.
For trained lifters with good technique, a well-prepared max attempt with safety pins or a spotter is common practice. Beginners usually get better information from rep-based estimates. If you have any injury or health condition, talk to a doctor or qualified coach before maximal lifting.
It depends on your goal. Many programs use roughly 60 to 80% for building muscle with moderate reps, and 80 to 90% or more for strength work with low reps. The percentage chart shows the load for each step so you can match it to the program you follow.
Yes. Choose kg or lb before you enter your numbers. The formulas are unit-free, so 225 lb for 5 reps gives about 262 lb with Epley, the same ratio as the kilogram example.
General fitness information, not medical advice. Talk to a doctor or qualified professional before changing your training or diet, especially with a health condition, an injury, during pregnancy or under 18.
